Detailed description of the gem setting process

A perfect piece of jewelry is infused with soul by designers and manufacturers, and their birth requires very complicated process steps. Step 1: The concept and design designer draws a sketch of his own idea by hand, and then uses the drawing software to make the sketch into a precise piece of perfect jewelry. The designer and the manufacturer have infused the soul. Their birth requires very complicated Process steps.　　　　 Step 1: Concept and design 　　　　 The designer draws a sketch of his own idea by hand, and then uses a drawing software to draw the sketch to a precise size on a computer to complete the initial design drawing.　　　　 Step 2: Craftsman carving wax 　　　　 The jewelry craftsman engraves the wax plate by hand according to the design drawings, and then uses the lost wax casting method to pour out the silver plate. The batch production of the wax plate requires the silver plate to press the rubber mold. This is the most demanding process in the jewelry making process. The silver plate made must be smooth and clean, and the structure of each part must be reasonable, and the position and size of the inlaid gems must be accurate.　　　　 Step 3: Inject wax into the rubber mold 　　　　 After the rubber mold is opened, perform the wax injection operation. The wax in the wax injection machine should be kept between 70-75 degrees, the wax liquid is injected into the film, the wax mold is taken out after cooling, and repeated in order to obtain multiple wax molds.　　　　 Step 4: Choose the matching stone 　　　　 According to the silver plate and wax model, select the matching stone with the right size, shape and color.　　　　 Step 5: Complete the wax type 　　　　 prepare all the wax plates required for this batch production.　　　　 Step 6: Planting a wax tree 　　　　 each wax ring is individually welded to a wax stick by hand, and finally a wax tree shaped like a big tree is obtained, ready for casting. Step 7: Weigh the rubber chassis before weighing the wax tree, and weigh the wax tree again after planting the wax tree. Subtract the results of the two weighings to get the weight of the wax tree. Or the density ratio of silver is converted to obtain the amount of metal to be cast. Step 8: Pour gypsum. Put the planted wax tree and the base plate on the stainless steel tube together, and slowly inject the corresponding weight of gypsum slurry along the inner wall of the steel tube, without the wax tree, naturally prevent 6-12 hours after vacuuming. Set plaster.　　　　 Step 9: Baking gypsum 　　　　 Baking the plaster mold for dewaxing, drying and casting heat preservation.　　　　 Step 10: Take out the plaster mold 　　　　 Take out the baked plaster mold, and at the same time prepare the metal solution that needs to be poured.　　　　Step 11: Pour liquid gold 　　　　Pour the melted gold water from the nozzle.　　　　Step 12: Centrifugal process casting 　　　　 Use a vacuum induction centrifugal casting machine to cast.　　　　Step 13: Fry and wash the plaster mold. The cast plaster mold is in a high temperature state. After it is taken out from the casting machine, it is placed in a natural place for 10-30 minutes, and then placed in cold water for frying. After the gypsum bursts due to shrinkage, take out the golden tree, brush off the large pieces of gypsum with a steel brush, soak it in 30% hydrogen acid for 10 minutes, and rinse after clamping to remove the remaining gypsum until the surface of the golden tree is clean.　　　　Step 14: Cut the casting 　　　　 Cut the jewelry on the golden tree along the bottom of the nozzle and dry it.　　　　Step 15: The barrel polishing process 　　　　 uses stainless steel abrasives and active organic synthesis solution into the drum, and rubs with rotation to make the surface smooth and bright.　　　　Step 16: Calendering process 　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　 the first and the second step step the step the step the step step\'s the step step the step the step the step' the step of the step\'s.　　　　Step 17: Polishing process 　　　　 Use a polishing machine to polish the jewelry until the surface is smooth and bright.　　　　Step 18: Select the diamonds 　　　　, manually sort the diamonds, pick out the appropriate color, cut, and size, and prepare for inlay.　　　　 Step 19: Inlay diamonds 　　　　 each diamond is set by hand.　　　　Step 20: Quality control 　　　　 will make fine inspections one by one to ensure that the quality is qualified.　　　　 The above is the information about gem inlay processing summarized by the author for you. The information comes from the Internet. If there is anything wrong, please forgive me. If you need to inlay, please pay attention to the official website of jewelry inlay. Jewelry inlay is waiting for your inquiry!