Several common diamond setting methods

What are the diamond setting methods? The setting method of the diamond can greatly affect the appearance of the diamond. It is understood that there are as many as 9 or more diamond setting methods, and each diamond setting method has its own unique advantages. 1. Prong setting: What are the methods of inlaying with metal 　　 diamonds? The setting method of the diamond can greatly affect the appearance of the diamond. It is understood that there are as many as 9 or more diamond setting methods, and each diamond setting method has its own unique advantages. 1. Prong setting: Use metal claws (pillars) to hold the diamond tightly. The metal rarely blocks the diamond, allowing a lot of light to enter from all directions, making the diamond in the center look bigger and more shining. Prong settings can be divided into six prongs, four prongs, and three prongs. Under the four-claw shape, you can see more diamonds, but the six prongs will be safer. This setting makes the diamond more outstanding and makes the diamond look radiant from any angle. But the claws are easy to scrape hair or clothes, and if the metal is deformed for a long time, it is easy to cause the claws to deform and the diamond to fall off. 2. Bezel setting: Use metal edging to seal the waist of the diamond in a metal holder (frame), and use the firmness of precious metal to prevent the diamond from falling off. Because the jeweler must strike the metal to fix the stone in the middle, this setting method is not suitable for gems with low hardness, which may cause the gems to crack. Hemming inlay is the second most popular diamond ring shape, not only has a modern appearance, but also very suitable for active people. This is a relatively strong and traditional setting method. When buying bezel-set diamonds, pay attention to the bottom of the diamond not to expose the bracket, and there should be no gaps between the bezel and the diamond, even and smooth, smooth and flat. There will be no hooks on clothes. 3. Card setting: Use the tension of the metal to fix the waist of the diamond (sometimes the waist and the bottom part). It is a very fashionable setting style, which can reflect the modern sense. The card setting is named because it relies on the tension of the metal itself to hold the diamond. As a result, it looks like the diamond is hanging between the two metal handles of the ring. People call it a clip setting. The card setting is a very distinctive shape, and the manufacturing process is not too complicated and the cost is not high. Card setting style setting also increases the safety of some diamonds, because it uses prong setting or bezel setting to further strengthen the diamond around or at the bottom. The disadvantage of this setting method is that the position where the gem is fixed by the metal is very limited, and the stress point is very small. If the notch is too large, it will easily cause the gem to loosen or even fall off. This method of setting requires slightly higher technical requirements. . 4. Track setting method: It is also called channel setting and wall setting. The groove is firstly driven on the precious metal bracket, and then the diamond is clamped into the groove. Orbital setting is suitable for setting diamonds of the same caliber. Diamonds or other precious stones are set next to each other in the middle of the metal groove to decorate both sides of the ring or the entire ring. This setting method can better protect the diamond. In addition, this style makes most of the diamonds connected into one piece, which can produce a visual effect that the diamond is larger or more than the actual one, and can make the surface of the ornament look smooth. However, the diamond is easily damaged during the setting process, and the degree of fixation of the diamond is average. 5. Nail setting: Use a tool to chisel out several small nails on the edge of the metal material to fix the diamond. You can't see any metal claws that hold the diamonds on the surface. The closely arranged diamonds are actually set in the metal tongue and groove. With this setting method, the diamond can reflect more sufficient light and make the diamond jewelry more shining. If the entire ring is set with nails, it is difficult to change the size of the ring. We strongly recommend that when customizing a ring, be sure to determine the size of the ring. 6. Press setting: The stone is separated from the stone by metal, and is tightly fixed by the left and right metal bars. This setting can be used to set off the center stone, or just use this setting method for wedding rings. 7. Hidden setting, also known as wiping setting, is a very stable and long-lasting setting method by setting the diamond in the thicker or larger area of u200bu200bthe metal. The diamond will not be exposed. This inlay method has no claws, and the jewelry looks smooth and clean, suitable for daily wear. In the market, this inlay method is often used to make ring pairs. The above are several common diamond setting techniques. If you want a larger diamond, you can choose a claw-set diamond ring, and if you want a stronger diamond, then bezel setting and hidden setting are the best choices. The specific purchase Inlaid diamond rings can be purchased according to your needs. This article comes from: Jewelry setting